HPA-82

Home

Products

Home Audio/Video

HPA-82

Click for larger image

Reliability through quality and simplicity

Telephone: +44(0)1299 250991

Email: sales@ikonavs.com

May also be
of interest

HPA-82

The HPA-82 is a 40 watts per channel stereo amplifier and is the ideal audio solution for small and medium size rooms which require a little more power than the SGA-40.
Fits a standard 2 gang back box of 35mm depth. (Not supplied)

Buy direct. Supplied with UK power supply.

Price includes VAT and UK delivery.

For outside the UK please email your requirement to sales@ikonavs.com

SGA -40
Amplifier

Introduction Technical Specification Installation

The iKON HPA-82 is a wall mountable amplifier with four unbalanced stereo audio inputs. It is manufactured on a UK twin gang white painted flat steel panel but for applications that require a raised profile to match other accessories, a suitable moulded mounting frame is included.

The HPA-82 fits a standard UK format double back box and requires only a 35mm depth, although a 44mm box is recommended.

The HPA-82 uses a 90% efficient class D design and has a RMS* output of 40 watts per channel into 8 Ohms when powered from the included 24V power supply, and as most quality loudspeakers are 8 Ohms, maximum efficiency is assured.

Two inputs are on the rear, connected via screw terminals for permanent connections, and two inputs on the front panel as 3.5mm stereo jack sockets. Inserting a jack into the front socket will automatically disconnect the rear inputs making the HPA-82 easy to install & use. DC power is connected via either the DC connector or screw terminals on the rear.

Introduction Technical Specification Installation

* The HPA_82 is a class D switching amplifier so the RMS values are RMS equivalent, this is that they give the same Sound Pressure Level using music or speech from a loudspeaker as a linear amplifier delivering the quoted RMS level.

Power Output, 12V Stereo Mode.	20W RMS* Per Channel into 8 Ohms.	Minimum input for full power	-6dB

Power Output, 24V Stereo Mode	40W RMS* Per Channel into 8 Ohms.	Protection	Integral, auto resetting, current limit & thermal protection. Integrated click & pop suppression

Bandwidth	20Hz to 20KHz +/- 1dB	Power Source	24V DC @ 2.1A (supplied)

THD & Noise	<0.3%	Power Connector	Screw Terminals or 3.5mm DC plug

S/N Ratio	76dB	No signal current	(24V) 56mA

Gain	26dBu	Standby current	(24V) 20mA

Coupling	Input: AC; Output DC.

Introduction Technical Specification Installation

Warning Disconnect power and unplug the unit from the power source before installing or removing.
The amplifier may become warm to the touch when in use.

The HPA-82 fits a standard UK back box with a minimum depth of 35mm. It will fit most metal recessed, surface metal & plastic as well as dry liner and dado mounting boxes. If possible a 44mm deep box is to be preferred as this makes wiring easier.

Cable entry into the box can be from any combination of the knockouts but it is recommended that the audio input cables are kept separate from both the DC and speaker cables if at all possible. Close proximity will cause no damage but could induce noise.

Power

The amplifier is DC powered and this should be fed from the supplied power supply. This can simply be plugged into the DC socket or if a remote PSU is used, it can be connected to the screw terminals provided.
A mains power connection will be required for the power supply achieved by plugging the supplied cable into an adjacent socket. If the cable needs extending or connecting into a fused spur then the services of a qualified electrician to carry out the connection is recommended.
Please note that for UK installations in domestic premises connection by a part ‘P’ registered electrician is mandatory.

If using the screw terminals on the rear PCB, please ensure correct polarity when connecting.

Environmental

The HPA-82 amplifier is not IP rated and should not be used in Bathrooms, outdoors or similar damp environments unless provided with additional protection of suitable IP rating.